JVC V.NETWORKS VN-C10 Uživatelský manuál

INSTRUCTIONSModelV.NETWORKSLWT0095-001CVN-C10For Customer Use:Enter below the Serial No. which islocated on the body. Retain thisinformation for futur

10(Side and rear views)Controls, Connectors and Indicators (continued)Introduction9 Ventilation openingFor the internal cooling fan. Install the cam-

11Connection ExamplesNetwork ConnectionPeer-to-Peer ConnectionVN-C10VN-C10LAN INTERNETPCPC Images are automaticallyupdated at a regular interval.FTP S

12Set the camera in the following procedure.Preparation ProcedurePreparations☞ Page 13☞ Page 19☞ Page 43☞ Page 44☞ Page 55☞ Page 61❈ If multiple PCs a

131-1 Attaching a LensAttach a lens in the following procedure.1.Before attaching a lens, check the mountmethod of the lens.VN-C10 is set for CS-mount

14Connect the camera to DC 12 V or AC 24 V.1-2 Connecting the Power CordPreparations (Step 1 Connection and Installation)CLASS 2 ONLY For USAISOLA

151-3 Connecting a LAN CableConnect the camera to a hub or a PC by using a LAN cable.NoteFor 100 BASE-TX, use a CAT-5 cable.POWERG2211OUT COMALARMDC12

161-4 Connecting the Alarm I/O TerminalsConnect the alarm I/O terminals with external equipment such as a sensor, buzzer,etc.Input Requirements• No-vo

17This terminal is for connecting with an alarm annunciator such as an indicator, alamp or a buzzer.1-4 Connecting the Alarm I/O Terminals (continued)

181-5 Installing the CameraPreparations (Step 1 Connection and Installation)[Fall Prevention] WARNING• Special care is required if the camera is insta

192-1 Installing the SoftwareInstalling V.Networks Controller1. Select [Setup.exe] found in the [JVC] folder.2. Proceed by following the instructions

2PORTABLE CART WARNING(symbol provided by RETAC)S3125AIMPORTANT SAFEGUARDS1. Read all of these instructions.2. Save these instructions for later use.3

202-2 Setting the PC’s IP Address for Windows XPPreparations (Step 2 Setting the Network)After attaching the camera, proceed to set the IP address of

212-2 Setting the PC’s IP Address for Windows XP (continued)3.Select [Internet Protocol (TCP/IP)] and click [Properties].4.Select [Use the following I

222-2 Setting the PC’s IP Address for Windows 2000Preparations (Step 2 Setting the Network)After attaching the camera, proceed to set the IP address o

232-2 Setting the PC’s IP Address for Windows 2000 (continued)Select [Use the following IP Address].4. Click [IP Address] in [TCP/IP properties].5.Cli

242-3 Setting the IP Address for VN-C10 with V.Networks Setup ToolPreparations (Step 2 Setting the Network)Set the IP address for VN-C10 by using the

252-3 Setting the IP Address for VN-C10 with V.Networks Setup Tool (continued)NoteIn a system where more than one VN-C10 are used, turn on the power f

261. Select [Start], [Programs], [V.NETWORKS] and then [vn-c10u Setup Tool] to start up[V.Networks Setup Tool].2-4 Other Settings with V.Networks Se

27VN-C10 is equipped with an access protection (security) function that, by settingpasswords, regulates users of the connected PC.Setting and cancella

28This section describes alarm setting.Alarm input is activated in the following cases.• Input signals are received from an input terminal located on

292-4 Other Settings with V.Networks Setup Tool [2. Alarm Setting] (continued)1 Alarm 1Select [ON] to convert signals input to the[ALARM INPUT 1] term

3Safety PrecautionsCAUTION:TO REDUCE THE RISK OF ELECTRICSHOCK. DO NOT REMOVE COVER (ORBACK). NO USER-SERVICEABLE PARTSINSIDE.REFER SERVICING TOQUALIF

30Preparations (Step 2 Setting the Network)This section describes the setting of the motion detection function which enables VN-C10 totrigger an alarm

312-4 Other Settings with V.Networks Setup Tool [3. Motion Detection Setting] (continued)V.Networks General SettingRefresh IntervalThe reference image

322-4 Other Settings with V.Networks Setup Tool [4. Recording Setting]Preparations (Step 2 Setting the Network)This function records the image to the

332-4 Other Settings with V.Networks Setup Tool [4. Recording Setting] (continued)3.OthersSet the recording action when the memorycapacity for recordi

34VN-C10 is equipped with an FTP client function which regularly uploads still imagesto an existing FTP server, thus enabling simultaneous image monit

352-4 Other Settings with V.Networks Setup Tool [5. FTP Client Setting] (continued)9 Error Recovery(Connection error)Specify a recovery action when an

362-4 Other Settings with V.Networks Setup Tool [6. Multicast]Preparations (Step 2 Setting the Network)Select [Multicast Mode].Selecting [Multicast Mo

372-4 Other Settings with V.Networks Setup Tool [6. Multicast] (continued)VN-C10 multicast addresses on the network can be searched.1.Start up [V.Netw

38Either JPEG or MPEG4 can be selected as the image compression format.1.Start up [V.Networks Setup Tool] and for the compression format, select JPEG

39An HTML file can be set as the default page of the web browser.1. Start up [V.Networks Setup Tool] and select [Web].2-4 Other Settings with V.Networ

4Contents ... 4Features ...

402-4 Other Settings with V.Networks Setup Tool [10. FTP Server]Preparations (Step 2 Setting the Network)Using FTP client software, HTML pages, GIF an

412-4 Other Settings with V.Networks Setup Tool [11. Time Setting]This section describes how to set the standard time for VN-C10. NTP can be usedfor

42NoteFor connecting VN-C10 with the factory settings, either one of the environments describedbelow is required.•Environment where no DHCP server exi

433-1 Back-focus Adjustment<For a fixed-focus lens>If focus cannot be attained using the focus ring ofthe lens, adjust the back-focus as follows

444-1 Starting Up V.Networks ControllerOperations (Step 4 Setting with V.Networks Controller)With the installed Controller, camera images can be monit

4512 3 41 FileNew : Creates a new file ifthe camera is con-nected for the firsttime.Delete : Deletes a file.Motion Detect Standby: For selecting thec

464-3 Motion Detection StandbyWith [V.Networks Controller] running, automatic connection will be activated uponreception of motion detection alert fro

47NoteNote● With MPEG4, the following settingsare not available.• 640x480• Upside Down● In the Fine mode, image details canbe checked.Not suitable whe

48With [V.Networks Controller], settings for image quality such as the imagecompression rate, white balance, etc., can be done.1.Select [Setting] and

494-5 Setting the Image Quality (continued)Photo-metering Area1 Compression RateSets the image compression rate. A lowercompression rate means a highe

5Step 4 Setting with V.Networks Controller4-1 Starting Up V.Networks Controller ... 444-2 Function Settings

504-6 Frame RateSets the maximum number of images perminute that are sent from VN-C10. This valueis set to “15” at the factory.NoteThe actual number o

51With [V.Networks Controller], it is possible to set the action to be taken uponreception of an alarm signal.1.Select [Setting] and [Alarm Setting].4

521 MessageWhen an alarm is received, the messageentered into the text box is displayed. Themaximum number of characters that can beentered is 100.2 R

534-8 Time StampWith [V.Networks Controller], the [Time Stamp] function can be set. This functiondisplays the date and time on the camera images, and

544-9 Changing the Registered InformationWith [V.Networks Controller], registered information on camera connection etc. canbe changed.1.Select [Settin

5516234 5[V.Networks Controller] can be used to select the camera, record and playback thecamera images etc.(The Controller screens are identical with

56Operations (Step 5 Operations with V.Networks Controller)[V.Networks Controller] can be used to save camera images to a file.1.Click the [REC] butto

57For playback, select the file saved with the record function of [V.Network Controller].The playback function cannot be effective while moving images

58Operations (Step 5 Operations with V.Networks Controller)5-3 Playback (continued)3.Click .Slidebar•Moves toward the right as the playback timeprogr

59Record/Playback time• Do not record or play a file that exceeds 2 GB with [V.Networks Controller]. With Windowsapplications, data in excess of 2 GB

6FeaturesIntroduction• VN-C10 uses a 1/3-inch CCD with 380,000 pixels, enabling monitoring of high quality images.•For the compression method, in addi

605-5 Snapshot1.Click the [SnapShot] button.[SnapShot] buttonSelect [File] and [Save].Specify the folder into which the file is saved.2. The [Snap] sc

61The following environment is required for viewing and operating VN-C10 with a Web browser.It is necessary for the PC to satisfy the technical requir

62Security level<Operator><User> <Administrator>Top page (index-e.html)Still image page (still-e.html)Moving image page (java-e.html

63Start up the web browser. Specify the factory-set web page address of VN-C10.(With the factory-set IP address entered, the web browser displays the

64Operations (Step 6 Operations with a Web Browser)6-4 Settings with a Web BrowserIP address, image quality, alarm, FTP, etc. can be set with a Web br

65Click [Apply] to update the settings.Other Settings:http://******/config-e.html (****** represents the URL of VN-C10.)The settings can be changed in

66Operations (Step 6 Operations with a Web Browser)6-4 Settings with a Web Browser (1. Other Settings) (continued)Item EffectDHCP Sets whether to use

676-4 Settings with a Web Browser (1. Other Settings) (continued)Note• Password Protection FunctionVN-C10 is equipped with a security function for res

68Operations (Step 6 Operations with a Web Browser)6-4 Settings with a Web Browser (2. Image Settings)Image Quality Setting Window:http://******/conf

696-4 Settings with a Web Browser (3. View Settings)View Setting Window:http://******/viewconfig-e.html (****** represents the URL of VN-C10.)Item Eff

7Required Operating EnvironmentUpgrading the ApplicationFor information on upgrading the application, visit the following website.http://www.jvc-victo

70Operations (Step 6 Operations with a Web Browser)6-4 Settings with a Web Browser (4. Alarm Settings)Alarm Setting Window:http://******/alarm-e.html

716-4 Settings with a Web Browser (5. FTP Settings)FTP Client Setting Window:http://******/ftp-e.html (****** represents the URL of VN-C10.)(This func

72Operations (Step 6 Operations with a Web Browser)6-4 Settings with a Web Browser (5. FTP Settings) (Continued)Item EffectFTP Function For enabling/d

73Hyperlink to the Home pageStill Image Page:http://******/still-e.html (*******represents the URL of VN-C10.)This page displays only still images. Th

74Operations (Step 6 Operations with a Web Browser)6-6 Viewing Moving ImagesHyperlink to the top pageMoving Image Page:http://******/java-e.html (****

75<IMG SRC=“http:// ****** /still.jpg”> ( ****** represents the URL of VN-C10.)<IMG SRC=“http:// ****** /push.jpg”> ( ****** represents t

76TroubleshootingForgotten the VN-C10 IP ad-dress that was changed with[V.Networks Setup Tool].Unable to record.While “Now Connecting…” isbeing displa

77MAC addressBF LOCKU1-32138146411/4 – 20UNC717035554264.5SpecificationsLAN standard IEEE802.3, IEEE802.3uCommunication protocol TCP/IP, UDP, HTTP,

78VICTOR COMPANY OF JAPAN, LIMITEDPrinted in JapanLWT0095-001CR is a registered trademark owned by VICTOR COMPANY OF JAPAN, LTD.R is a registered trad

8Operating Precautions● VN-C10 is designed for indoor use. For outdoor use, prepare a proper housing to cover andprotect the camera.● The product shou

9Controls, Connectors and Indicators(Front, top and side views)1 Lens mountThe mount for attaching a lens. Either a C-mount or a CS-mount lens can be